Sig Sauer - Manufacturers - Top Gun Supply

Factory Sig Sauer replacement firing pin block spring for the Sig Sauer P238 and P938 pistols.

Sig Sauer factory Firing Pin Retaining Pin for P227, P220, P226, P229, P229. P224 and P239 stainless steel slide models. This is the spiral or coiled pin found on later model pistols. Not for use on older pistols or those that use the solid FPPP or the 2 piece roll pins. For slides with short extractors only.

Factory replacement Nickel grip plate washer (1) for P220, P225, P232 and P245.

Factory replacement grip plate screw (1) for P238 and P938. Black finish. Made by Sig Sauer, these are replacement screws for the Sig Sauer P938 and P238.

Factory replacement grip plate screw (1) for P229 .40/.357. If you have an Elite model using the factory wood grips, you will need P239 grip screws, which are longer.

Factory replacement plastic recoil spring guide rod for the Sig Sauer P250 Compact in 9mm.

Sig Sauer factory Hammer for P220, P225, P226, P228, P229 and P245 models, nickel finish. Replaces part #34280325N

Sig Sauer factory Hammer for P220, P225, P226, P228, P229 and P245 models, black super finish.

Sig Sauer factory Hammer Pivot Pin, all P series models. Genuine OEM gun parts ensure proper fit and finish as well as keeping your Sig Sauer pistol reliable.

Sig Sauer Hammer Pivot Pin for the Sig Sauer P238 380ACP pistol.

Sig Sauer factory Hammer Reset Spring for P220 and P245 models.

Sig Sauer factory Hammer Stop for P225, P228 and P229 models.

Sig Sauer factory Hammer Stop Pin for P220 and P245 models.

Sig Sauer factory Hammer Strut for P220, P226, and P229 DAK models.

Sig Sauer factory Hammer Strut (new style) for P220 and P245 models. Will not fit older spurred hammers. To use this strut with those models, you will also need the rounded hammer, hammer reset spring and most likely a new sear.

Sig Sauer factory Hammer Strut Roll Pin (old style) for all models. Pin installs on the base of the Hammer Strut and retains the Mainspring.

Sig Sauer factory Inner Roll Pin for all carbon steel slide models.

This exclusive P365-XMACRO IWB BlackPoint Tactical holster has been designed to be a minimal appendix carry holster that can be easily configured to be worn comfortably in any IWB, strong-side position. It features a concealment strut that acts as a lever on the holster against the inside of the belt, pressing the firearm's grip into the body and aiding in concealment. Designed to be used with or without a ROMEOZero installed.

The concealment strut has built-in height adjustment allowing it to be moved to match the user’s belt height. The back of the concealment strut has channels to capture the hardware which aids in the height adjustment. The holster ships with all the needed hardware so that the concealment strut can be removed while retaining the full functionality of the holster. This quick swap is recommended for users who wish to carry in a position other than appendix. Features an adjustable double-finger metal belt clip to prevent unwanted removal. The belt clip cant and ride height can be quickly modified by simply loosening the screws on the belt clip, adjusting the clip position, and tightening. This provides the end-user with a wide range of adjustability so they can find the carry position most comfortable for them. This holster has a factory optic relief cut to allow the use of ROMEOZero where desired. The screws underneath the trigger guard allow the user to easily adjust the tension on the holster within a set range. The belt clip rides on a strong custom-formed Kydex wing for more comfortable carry, allowing the holster to flex just the right amount.

Right-handed configuration